Ramset T3ss

Versatile

Without changing power or color loads fasten into:

Concrete
Hollow Block
Pan Deck
Steel

Safe!

Safety Managers recommend the T3 because there's no licensing required.

Lower Recoil Reduces Operator Fatigue
Quieter than Drilling & Anchoring or Powder
Eliminates Exposure to Concrete Dust (Silicosis)

Tool Specs T3ss

Weight	7.0 lbs
Height	15"
Length	13-1/2"
Power	100 joules
Fuel Cell Design	One step - just insert into tool
Tool Design	Customized for user application
Fastener/Pin Diameter	0.125
Fasteners	Single pin fasteners are preassembled with popular clips for convenience
Fastener Assembly	Fasteners are preassembled, ready to shoot
Fastening Flexibility with different pin sizes	One assembly per shot

Troubleshooting

Preparing Tool for Operation — Battery/Charger Problems

SYMPTOM	POSSIBLE PROBLEMS	SERVICE
Battery Cell does not appear to accept charge. Green charger light does not come on.	Inoperative indicator lights on charger	Try Battery in tool after 3 hours on charge cycle. If tool LED is green, charger lights are not working properly. Replace charger or monitor charging time to ensure ?Battery Cell has adequate time for recharging. It’s normal for Battery to feel warm after properly charging.
	Battery Cell damaged or cycle life exhausted	Replace Battery Cell
	Damaged charger	Discontinue use immediately and unplug from power source. Replace charger and tag or dispose of charger to prevent accidental reuse or connection to power source.
Flashing lights on charger base unit	Damaged Battery Cell	Replace Battery Cell
Flashing lights on charger base unit	Battery completely drained	Allow Battery to charge for 5 minutes

Normal Stage of Operation

SYMPTOM	POSSIBLE PROBLEMS	SERVICE
Fan does not run — tool LED is off	Battery in off position	Fully insert Battery
	Battery Cell is not charged	Charge Battery Cell according to Operating Manual
	Battery terminals or battery contacts are oily, dirty, or corroded	Clean Battery Cell terminals. Battery Cell contacts are required.
Fan does not run, or runs slower than normal — LED is red	Battery Cell is discharged	Charge Battery Cell
Fan does not run, tool LED flashes red/green	Possible electronics error	Remove, reinsert the Battery. Contact Authorized Ramset Distributor Sales Representative for service.

Pre-Combustion/Combustion Stage of Operation

SYMPTOM	POSSIBLE PROBLEMS	SERVICE
Work Contacting Element does not depress fully — tool does not operate	Work Contacting Element is bent, or build-up of debris in nose restricts operation	Remove and inspect Work Contacting Element. Repair or replace as required.
	O-Ring pinched	Contact Authorized Ramset Distributor Sales Representative for service
(For T3 Magazine tool only)	Tool is out of fasteners	Add fastener strip
Tool will not cycle — fans runs, LED is green	Fuel cell is empty	Replace Fuel Cell
Tool will not cycle — fans runs, LED is green	Spark does not occur	Contact Authorized Ramset Distributor Sales Representative for service

Power/Exhaust Stage of Operation

SYMPTOM	POSSIBLE PROBLEMS	SERVICE
Tool operates properly, but fasteners do not drive fully	Battery cell is discharged	Charge Battery Cell
	Fuel Cell is low	Check Fuel Cell according to Operating Manual and replace as required
	There may be loss of seal in combustion chamber	Press Work Contact Element against workpiece for one minute. Pull trigger. If fastener does not drive, there is a leak that requires service.
Tool operates erratically or appears to be losing power — tool LED is green	Fuel Cell is low	Check Fuel Cell according to Operating Manual
	Filter element is dirty, causing tool to overheat	Remove Filter element and clean according to Operating Manual. Use safe cleaning solution to remove stubborn debris.
	Tool Sleeve or O-Rings are dirty	Clean tool per Cleaning Procedure

Returning/Purging Stage of Operation

SYMPTOM	POSSIBLE PROBLEMS	SERVICE
Tool operated and drove fastener, but piston did not return to start position	Built-up dirt and debris on Piston or in Nose bore	Clean Piston and Nose bore with safety solvent. See Cleaning Procedure.
	Mushrooming of Piston Tip	Contact Ramset Distriburor Sales Representative for service.
	Exhaust ports on the Sleeve are dirty or clogged.	Return tool to Authorized Ramset Sales Representative for serice.
	Tool (Sleeve) or O-Rings are dirty	Clean tool per Cleaning Procedure
Tool does not open after tool fires	Work Contacting Element is bent, or tool is dirty	Clean tool or replace Work Contacting Element as required.
	Filter element is dirty, causing tool to overheat	Remove Filter element and clean according to Operating Manual. Use safe cleaning solution to remove stubborn debris.
	Tool Sleeve or O-Rings are dirty	Clean tool per Cleaning Procedure

If the T3ss or T3 Magazine tool will not operate after following the above service directions, return the tool to a Ramset Distributor Sales Representative for service.